Vehicle diagnostic guide

Nissan Altima

Model years: 2019-Present Β· Japan Β· Sedan

Use this guide to understand diagnostic trouble codes, investigate dashboard warning lights, and plan the next diagnostic steps for your Nissan Altima. Exact procedures and component locations can vary by model year, engine, trim, and market.

Manufacturer

Nissan

Model Years

2019-Present

Body Style

Sedan

Diagnostic Resource

OBD-II / OBD2

OBD2 Diagnostic Trouble Codes

Explore available diagnostic code explanations. The list below includes codes whose existing vehicle tags match Nissan Altima; compatibility with your exact vehicle configuration must still be confirmed.

B0001 β€” Driver Frontal Stage 1 Squib Circuit Resistance Low

The driver airbag squib (firing circuit) has lower resistance than expected, indicating a wiring or connector issue.

View code β†’

B0051 β€” Side Impact Sensor Left Front β€” Circuit Low

The SRS/airbag control module has detected a low-voltage or open-circuit fault in the left front side-impact sensor, which helps trigger side airbags and seat-belt pretensioners during a side collision.

View code β†’

C0037 β€” Left Rear Wheel Speed Sensor Circuit

The ABS/EBCM has detected an abnormal or missing signal from the left rear wheel speed sensor (WSS), which is used to calculate wheel speed for ABS and traction/stability control.

View code β†’

C0051 β€” Steering Wheel Angle Sensor Circuit

The vehicle's stability control module has detected a fault in the steering wheel angle sensor circuit, which reports how far and how fast the steering wheel is turned to the ESC and ABS systems.

View code β†’

C0061 β€” ABS Solenoid 1 A Circuit

The ABS/EBCM has detected an electrical fault in the ABS hydraulic modulator's solenoid 1A circuit, which controls hydraulic pressure to one of the wheel brake circuits during ABS activation.

View code β†’

P0016 β€” Crankshaft/Camshaft Position Correlation Bank 1 Sensor A

The crankshaft and camshaft position signals are out of sync on Bank 1. This indicates a timing issue.

View code β†’

P0089 β€” Fuel Pressure Regulator Performance

The fuel pressure regulator is not maintaining correct pressure.

View code β†’

P0093 β€” Fuel System Leak Detected β€” Large Leak

The ECM has detected a large fuel system leak based on a significant, rapid drop in fuel rail pressure that cannot be explained by normal injector demand.

View code β†’

Important: an OBD2 code identifies a detected condition or system. It does not, by itself, prove that a particular part has failed. Confirm the code, symptoms, service information, and diagnostic test results before replacing parts.

Dashboard Warning Lights

A warning light can indicate anything from a routine maintenance reminder to a fault that needs immediate attention. Identify the symbol and read the vehicle owner's manual before deciding whether it is safe to continue driving.

Check Engine Light

Learn about engine and emissions warnings and how to begin OBD2 diagnosis.

Read guide β†’

Browse Warning Lights

Explore the warning-light directory for additional symbols and explanations.

Read guide β†’

Fuse Box Location and Electrical Checks

Fuse locations, ratings, and layouts can differ across Nissan Altima model years, engines, and trim levels. Use the correct owner's manual or service information for your vehicle identification number (VIN).

  1. Check the owner's manual for the interior fuse panel and under-hood fuse box locations.
  2. Identify the fuse by its listed circuit and specified amperageβ€”not by appearance alone.
  3. Switch off the vehicle and follow the manufacturer's precautions before inspecting a fuse.
  4. Replace a blown fuse only with the specified rating. If it blows again, investigate the underlying electrical fault rather than fitting a higher-rated fuse.

A model-specific fuse diagram is not currently provided on this page. Do not rely on a diagram from a different model year or vehicle configuration.

Engine Sensors and Diagnostic Checks

Sensor positions and test procedures depend on the engine and vehicle configuration. These general checks can help you decide what to investigate before ordering replacement parts.

1

Read the stored trouble codes

Use a compatible scan tool to retrieve stored and pending codes. Record the exact code and any available freeze-frame information before clearing anything.

2

Compare the code with the symptoms

Note when the problem occurs, whether the engine is cold or warm, and whether there is rough running, loss of power, unusual noise, or a change in fuel consumption.

3

Inspect the relevant circuit

Depending on the code, a technician may check connectors, wiring, power supply, grounds, sensor readings, air leaks, or mechanical conditions.

4

Confirm the repair

After the fault is repaired, follow the correct verification procedure and check whether the code returns. Some monitors need a specific drive cycle to complete.

Safety note

Stop safely and seek professional assistance if a red oil pressure or overheating warning appears. If the check engine light flashes while the engine is running roughly, reduce load and stop when safe; continued driving may damage the catalytic converter.

More Nissan Models

Explore diagnostic information for other models from the same manufacturer.

Frequently Asked Questions

How do I read OBD2 codes on a Nissan Altima?

Connect a compatible scan tool to the vehicle's diagnostic connector, follow the tool's instructions, and record the complete code. The connector location and supported diagnostic systems may vary by year and configuration.

Does an OBD2 code tell me exactly which part to replace?

No. A code points to a detected fault or system. Diagnosis may require checking wiring, connectors, sensor data, mechanical conditions, and manufacturer-specific procedures.

Are the same diagnostic codes valid for every model year?

Not necessarily. Engine options, regional specifications, emissions equipment, and vehicle electronics can affect which codes and diagnostic procedures apply. Confirm the information for your exact vehicle.